Ultra-Lightweight and stylish replacement oil filler cap for frames with filler near the headstock. Made from Anodised Aluminium for lightness and durability

£4.29 Inc VAT

Ultra-Lightweight and stylish replacement oil filler cap for frames with filler near the headstock. Made from Anodised Aluminium for lightness and durability

£4.29 Inc VAT

Ultra-Lightweight and stylish replacement oil filler cap for frames with filler near the headstock. Made from Anodised Aluminium for lightness and durability

£4.29 Inc VAT

Ultra-Lightweight and stylish replacement smaller oil filler cap for frames with the filler on the diamond close to the saddle. Made from Anodised Aluminium for lightness and durability

£3.76 Inc VAT

Ultra-Lightweight and stylish replacement smaller oil filler cap for frames with the filler on the diamond close to the saddle. Made from Anodised Aluminium for lightness and durability

£3.76 Inc VAT

Ultra-Lightweight and stylish replacement smaller oil filler cap for frames with the filler on the diamond close to the saddle. Made from Anodised Aluminium for lightness and durability

£3.76 Inc VAT

Due to new regulations in 2008 you must have an extra guard separate from any chainguide near the rear sprocket. This guard is lightweight, simple to fit and
supplied complete with P-clip and fixings.

£7.93 Inc VAT

Light Weight Rear Wheel Adjuster. This light weight adjuster is perfect to keep you rear wheel properly adjusted. It has a helicoil thread to make it hard wearing and to cope with the dirt, and a plastic insert to stop the adjuster coming loose during racing. The adjuster can be fastened by hand, by 17mm A/F spanner, or by socket.

£4.20 Inc VAT

Quick Release Primary Chain Guard Mount Assembly. These primary chain guard mounts are a great way off saving valuable time between rides. Using a clip system it only takes seconds to remove the primary chain guard rather than minutes with the conventional bolts. Included in the Assembly is one mount, bolt, plastic washer and clip.

£4.50 Inc VAT

Countershaft Retainer Kit. For many years riders have had problems trying to stop their countershaft from moving while racing. Here is a specially designed kit which does just that. It has been designed to work with any Countershaft and frame available of the market. The kit comes complete with bolt, adjuster, block and all the other necessary nuts, bolts and washers to stop the countershaft from moving.

£18.40 Inc VAT

Exhaust Front Bracket Assembly. These stylish exhaust brackets are the perfect solution for securing your exhaust. Using a bolt through the bottom hole in your engine you can attach an exhaust p-clip to this bracket which will support to your exhaust.

£6.90 Inc VAT

Primary Chain Sling Pin Bolt. Every bike needs to have a sling pin bolt under the speedway regulations to prevent damage occurring when the primary chain breaks. Our bolt has a 6mm hex socket so you can tighten it using an allen key and a 17mm A/F spanner.

£3.35 Inc VAT

Rear Wheel Stud with a 6mm hex socket. These rear wheel studs have been made so you can fit them to you wheel quickly and easily. This have been achieved by putting a hex socket in the end so you can use an allen key to tighten the stud.

£2.00 Inc VAT

M10 Rear Sprocket Nuts made from high quality steel and bright Zinc plated.

Sold in packs of 10.

£2.06 Inc VAT

Dirt Deflector Stop. When your existing stop gets worn it allows the dirt deflector to sit lower and cause problems in deep start line ruts. By fitting a replacement you can lift it back to the correct height. Comes complete with cap head screw for ease of installation.

£3.25 Inc VAT

1 Inch Saddle Spacer with a 6mm Bore. Getting comfortable on your bike is very important. Here we have a 1 inch aluminium spacer which you can use to adjuster the height of your seat.

£0.60 Inc VAT

1/2 Inch Saddle Spacer with a 6mm Bore. Getting comfortable on your bike is very important. Here we have a 1/2 inch aluminium spacer which you can use to adjuster the height of your seat.

£0.50 Inc VAT

3/4 Inch Saddle Spacer with a 6mm Bore. Getting comfortable on your bike is very important. Here we have a 3/4 inch aluminium spacer which you can use to adjuster the height of your seat.

£0.55 Inc VAT

M5 Cup Washer. These are lightweight washers to be used with countersunk bolts.

Countersunk bolts can be purchased by contacting us direct for details.

£0.50 Inc VAT

M6 Cup Washer. These are lightweight washers to be used with countersunk bolts.

Countersunk bolts can be purchased by contacting us direct for details.

£0.50 Inc VAT

This durable plastic guard is made for the new style Jawa straight back ends. It can be fixed using cable ties and is also available in white.

£16.30 Inc VAT

This durable plastic guard is made for the new style Jawa straight back ends. It can be fixed using cable ties and is also available in black.

£16.30 Inc VAT

L/H Footrest Extension Plate - 65mm pitch. These extension plates are designed to bolt on to the original Jawa footrest plate and are ideal for longer legged riders who find the standard fitting too high. There are two types of plate depending on the version of footrest plate. This one has a pitch of 65mm between the two holes, which bolt onto the existing plate.

£15.75 Inc VAT

L/H Footrest Extension Plate - 70.5mm pitch. These extension plates are designed to bolt on to the original Jawa footrest plate and are ideal for longer legged riders who find the standard fitting too high. There are two types of plate depending on the version of footrest plate. This one has a pitch of 70.5mm between the two holes, which bolt onto the existing plate.

£15.75 Inc VAT

M6 Zinc Plated Steel Nyloc Nuts. Sold in packs of 20

£1.18 Inc VAT

M15 Zinc Plated Steel Nyloc Nuts. Sold in packs of 15

£1.18 Inc VAT

M10 Zinc Plated Steel Nyloc Nuts. Sold in packs of 10

£1.18 Inc VAT

M12 Zinc Plated Steel Nyloc Nuts. Sold in packs of 8

£1.18 Inc VAT